Eco-friendly heat pump for pool

Pools, regardless of size, require heating at any time of the year. For this purpose different devices to maintain the temperature.

The correct solution of this task is ideal heat pump for the pool. This is a special Converter, allowing you to more efficiently create thermal energy to heat water, without disturbing the surrounding environment.

Design and principle of operation

The main advantage of heat pumps is that they enable a fully automatic mode to heat water in the pool, but also to control in the desired range the level of its temperature.



The scheme of heat pump with refrigerant

According to owner reviews, this greatly simplifies the maintenance of such a facility. It uses to heat the water in the pool, and classical warmth.

The principle of operation is similar and works exactly like similar devices in heating systems when the heat consumer receives directly from the primary source: groundwater, soil, or air.

It is important to know: pipeline design "water-water" must be buried in the ground. Due to the constant heat of the ground waters, regardless of season, Parking in this pump can be carried out all year round. The main element, through which such heat pump takes heat directly from the source, this collector.

The better its heat transfer performance, the more efficient the work of the pump. It is equipped with a special substance like antifreeze, allowing it to absorb heat, with the slight difference in temperatures.

The main component inside these devices is the refrigerant. He circulates in the system changes its state from a liquid to a gas, by changing two factors: the temperature and pressure.

After that, the heat pump compressor compresses the incoming gaseous substance, resulting in a sharp increase in the temperature, and then the chain is passed the resulting heat. And then it is transferred to the final heat exchanger, which is the last link in the chain.

The main advantages

The main advantages of such pumps can be considered:

• the ability to maintain a constant specified by the owner, the level of water temperature throughout the pool;
• saving energy while converting it into heat. Thus, such devices may in the ratio 1:5 to make the electricity warm. Due to this, from 1 kW of consumed electricity yields approximately 4 kW of heat energy;

It looks like the heat loss from the usual outdoor pool

• eco-friendly, due to the lack of need of fuel combustion and the discharge of contaminants on the site;
• reliability and long service life. And in case of any problems in his work, it is turned off automatically and it signals a failure;
• easy to use, by automating the entire process makes it possible simply to select the desired temperature without additional manipulations;
• the maximum efficiency among all other types of heating not only on electricity consumption but also on the rate of heating.

Selection criteria

During the selection of such units should consider such factors as:

The conditions under which you will be using either an outdoor pool or assumes his position in the room. Where will be located the device, availability of the sources from which we can extract potential energy. If it will be in the building, what will be the type of its roof. The initial temperature of the water, as well as the necessary values. The volume of the pool. The more will be the amount of water is, consequently, a large should be the capacity of the unit. The presence of additional heat sources and ventilation, whether the heating or air conditioning (for rooms). The ability to easily connect not only to network, but also the water loop, which will make installation and maintenance much easier.




An example of the heat pump at the outdoor pool where communications are laid under the ground

For decorating indoor swimming pools quality parameters of air will be between 22°C to 24°C degrees and the pool water from 26°C to 27°C. Given these finite values, if no special request that you want to achieve, is to opt for heat pumps.

Operating conditions

Manufacturers give recommendations on the conditions of operation of such devices, depending on various characteristics.

So, in most cases, the pump must be placed above water level to increase efficiency. The run should be at an acceptable temperature level of the pool water and air around.



It looks like the pool and all utilities for heating water and filtering it

You must also comply with the operating conditions of the equipment. It is necessary that the level of humidity in the installation site does not exceed the acceptable values, and was not prolonged overloads and lack of overheating.

Good to know: to stop the pump quickly is not out of order, you need to take care of proper filtering of water coming toward him. This will not only serve you for a long time to pump, but also save the power consumption, which may rise due to improper use and inadequate working conditions.

Watch the following video review of one of the manufacturers of heat pumps for swimming pools:

SUBSCRIBE to OUR youtube channel that allows you to watch online, download from YouTube free video about the recovery, the rejuvenation of man. Love for others and ourselves, as the feeling of high vibrations — an important factor for improvement .



Put LIKES and share with your FRIENDS!

www.youtube.com/channel/UCXd71u0w04qcwk32c8kY2BA/videos

Subscribe -https://www.facebook.com//

 

P. S. And remember, only by changing their consumption — together we change the world! ©

Source: 6sotok-dom.com/uchastok/vodosnabzhenie/teplovoj-nasos-dlya-bassejna.html