Winter dog booth

In general, winter came to Vladivostok, and I was thinking about a new kennel for my yarder, in the old booth my Dusia stopped fitting ... I went to the Internet to appreciate...





It's kind of a whiff. The booth in one board - from 6 kilorubles((((())) Let them go to Sochi with such booths! It is decided to build on oneself, on one’s conscience and on the envy of enemies.



Study profile sites, smoked manuals ... Dog measured in centimeters, inches and parrots)



He drove to the market, bought 10 squares of larch carvings, 6 meters of a beam-five, 3 meters of a beam-three, 6 sheets of a heater "thermoplex" 5 cm and 2 sheets 3 cm ... 6 squares of polyethylene - millimeters, well, every little thing (holsters-blades etc.)



In fact, the culprit of the celebration came...



From this bar 5 * 5 make a frame - the bottom of the booth



Stitch it up with a wagon.



We build a frame on it, the front side is 10 cm higher for rainwater drainage.

7178787881

We put bars 3 * 3 for forming walls and manhole



Future entrance, pinched around the perimeter



With plastic, we say to a possible wind blowing into the crevices: “You will not pass!”



We cut thermoplex, five.



Bottom line.



Suture.



For cutting boards, we use the guillotine and the bosh circular, an excellent tool.



Now from the opposite - we collect the internal side walls, fasten them with screws to the racks.



So.



So?



We sew up the butt and in front of the booth, fasten them with screws to the bars of rigidity 3 * 3)



Sewing the walls with thermoplex



Take a day off and 2 liters of dark



After two liters of dark, fitting the dog into the booth, the booths - to the future installation site, about an hour of mat towards the site with the size of the booths depending on the size of the barbos ... It was decided to reduce it in all sizes by 10 cm. The topic as with a photo on an iPhone - pinch with two fingers and squeeze-increase here did not work (minus the technique from Apple, let me down iPhone), had to disassemble everything by zero.



5 cm were cut from each board on each side to remove already drilled fragments.



frame-piece



Booth explosion diagram before reduction)



The box lost 10 cm in all three dimensions.

187261

stiffness beams were put, the entrance is shifted to the end to the right, in connection with which an extra beam of stiffness was added, at the request of the family a lower brook was added - "We throw hay there, we need a seed so that it does not fall out," polyethylene is laid on the bottom, on top of it - a thermoplex.



I remembered that from the construction of the house there was this material - goes to the roof, one of the layers. foil + 5mm foil



I hit it on the bottom, sewed it up with a wagon.



Restored all internal walls



thermal insulation of the back of the booth in layers: tram, 5 mm heatisol, 3 cm thermoplex



polyethylene

623773

Scotch holds the polyethylene, before finishing. Under the bottom nailed legs 3 centimeters, so that the box on the ground did not stand.



The front end of the same scheme, already sewn up



The sides are the same, but there are no beams, and thermoplex is not 3, but 5 cm thick.



Re-fitting the dog, all right.



Not everything. When cutting the boards under the disk hit a knot, pulled the board, behind her glove, behind her fingers ... emergency room, injection, hospital, waiting for surgery



The next day I go to other doctors to minimize the damage.



The middle one suffered the worst of all, only memory remained of the bones and the tiny index and nameless suffered from the front side, everything was crushed to the bones there.



They put artificial bones in the middle, rebuilt tendons, sewn-stitched-gypsumed ... time will tell.



After 3 days in the bran and three more on injections, it was decided to continue.



All walls are sewn up, bevels are removed.



Roof.



roof - a view from the bottom: trimming, thermal glue, top thermoplex 5 cm.
P.S. Forgot - put a corner of 4 cm in the corners, for beauty. And the joints are too protected)



The glue of such a sandwich did not trust, applied another layer of the carriage, and right through to the screws. Closely.



From the bins got geotextile, put 4 layers, took on screws. It's a lid like that.



Of the same 4 layers of geotextiles made an apron at the entrance, but the solution is temporary, the other day I will buy a plastic-five transparent, it will be more interesting.



Put it in place. I had no time to put the couch inside, the dog had already climbed in and was not going to go out.
Total: the cost of the material is 10,500, work - about 5 days off, In the pluses - I and the dog are happy, in the minuses - an injury to the hand and minus one phalanx on the middle finger. You can kick.