657
LED light in the garage
It was bought at ebee / aliekspresse:
LED Tape 5m smd 5050, 60 diodes / m, ~ 15 lumens / diode, LED tapes 5m smd 3528, 60 diodes / m, ~ 5-7 lumens / diode waterproof. PSU ATX FSP 400W was available, corners too.
Garage ~ 6x4 m
22 photo.
02. Take the old waste plastic corners.
03. Select the appropriate length of
04. Cut the ribbon with 5050 diodes (warm white) to 3 parts of 99, 99 and 102 of the diode (multiple of 3 pcs. / 5 cm)
05. Cut the corners along the length of the tape
06. ribbon with 3528 diodes (cool white)
07. Cut a piece of 3 to 1, 5 meters / 90 pieces (as half a meter of the tape has already been used for illumination of car doors), soldered. The process of soldering is not filmed, it was uncomfortable.
08. Degrease plastic corner and sticking on the edge of the tape.
09. Prilep
10. Corners stuck with tape and soldered wires lie, waiting installation.
11. Priherachivaem building stapled to the rafters.
12. Tape 5050 to "place»
13. Tape 3528 to "place»
14. Bought terminals here are very comfortable.
15. Getting connected
16. A general view of connections
17. "bus" was used 4 mm2 to avoid a voltage drop, because total current consumption ribbons about 6 amps.
18. Test run
19. The yard is still day
20. This photo evening
21. Tapes (6 pieces) secured by turns cold / heat, etc.
22. View from the street at night. It was very bright and evenly (there are practically no shadows). Sorry, not filmed connection to the power supply (twisted in a heap all the yellow (+ 12V) and all the black wire (-)), we say to increase the cross section.
The total consumption of about 70 watts. Effort: 2-3 hours. Dengozatraty: 900 rubles.
Unprotected ribbon SMD 5050 later coated with a special polyurethane varnish from a container to protect from moisture.
Everything! You can kick!
LED Tape 5m smd 5050, 60 diodes / m, ~ 15 lumens / diode, LED tapes 5m smd 3528, 60 diodes / m, ~ 5-7 lumens / diode waterproof. PSU ATX FSP 400W was available, corners too.
Garage ~ 6x4 m
22 photo.
02. Take the old waste plastic corners.
03. Select the appropriate length of
04. Cut the ribbon with 5050 diodes (warm white) to 3 parts of 99, 99 and 102 of the diode (multiple of 3 pcs. / 5 cm)
05. Cut the corners along the length of the tape
06. ribbon with 3528 diodes (cool white)
07. Cut a piece of 3 to 1, 5 meters / 90 pieces (as half a meter of the tape has already been used for illumination of car doors), soldered. The process of soldering is not filmed, it was uncomfortable.
08. Degrease plastic corner and sticking on the edge of the tape.
09. Prilep
10. Corners stuck with tape and soldered wires lie, waiting installation.
11. Priherachivaem building stapled to the rafters.
12. Tape 5050 to "place»
13. Tape 3528 to "place»
14. Bought terminals here are very comfortable.
15. Getting connected
16. A general view of connections
17. "bus" was used 4 mm2 to avoid a voltage drop, because total current consumption ribbons about 6 amps.
18. Test run
19. The yard is still day
20. This photo evening
21. Tapes (6 pieces) secured by turns cold / heat, etc.
22. View from the street at night. It was very bright and evenly (there are practically no shadows). Sorry, not filmed connection to the power supply (twisted in a heap all the yellow (+ 12V) and all the black wire (-)), we say to increase the cross section.
The total consumption of about 70 watts. Effort: 2-3 hours. Dengozatraty: 900 rubles.
Unprotected ribbon SMD 5050 later coated with a special polyurethane varnish from a container to protect from moisture.
Everything! You can kick!
