766
Table Fender Stratocaster
Please do not break, I finish, I will inform you. Will be 14 ph and some text.
Good day dear comrades. Each found himself in a situation that needs a gift and not just a gift, but something very interesting and original. Especially gift for your girlfriend loves guitar. Internet is limitless and as a bottomless pit has no end. After long wanderings over the vast expanses, it was decided to make a coffee table. This is the first of its kind. In my opinion turned out not bad. In the course of action I will comment on what is happening.
Was first bought a wooden shield required size. And in A1 format required stencil printed.
Since the shield was a bit more than what was intended and had to increase the size of the handles.
Armed with a jigsaw began the process of cutting out this miracle-shaped table. Dumb was the first time in the hands to keep the jigsaw. And it is necessary'm not zakosyachit.
About miracle first stage was successful. Severe cerebral process was waiting for me in the place where you had to make a smooth round holes. First drill was drilled small holes along the contour and then the same jigsaw were cut circles. Initially, it was difficult to call it a community. Similarity circles. Circles, they were only after aligning them with sandpaper to cut dressed kruglyashok and inserted into the drill.
When the ordeal was over with circles, it was decided to do a little rounded edge of the table, thereby eliminate irregularities he made a jigsaw. Well here it was difficult to automate the process and had to work handles. A piece of wood, sandpaper, first major, then smaller. And in the summer to do it as the second foul. Hands get tired, then go ten. But that will not do for his beloved.)) The morale support to friends and drink produced via fermentation of malt wort, and usually with the addition of hops. Bolt clear that beer.))
Form has been smoothed and again these circles. Too much, they stood their tangy. Had their smooth and slightly to grind off. Processing completed grinding medium, and then the finest sandpaper.
After the action moved from a dusty garage, balcony on the net. As the piece of wood was very bright and looked not so impressive and expensive, it was covered with several layers of water stains (oak). After the first coat immediately povylazili nezashlifovannye scratches are so nebyli visible. The second layer covering these scratches began a very personal look creating a grungy effect. It's a guitar fretboard (excuse)))
Then came the most difficult moment and glasses. It's one thing to work with a drill or bar with sandpaper, another small brush. A blueprint was dealt circuit Fender.
A night not so long already. Shaking hands with a lot of thoughts and phrases that would be worth all this zapikali and paint.
Wow. Almost everything is ready. The final touches on a pair of applying layers of lacquer.
Binding the three legs to our table.
And voila, done.
She was very happy. Later in the hole to insert cups in the color table.
That's all. Thank you for your attention.
Source:
Good day dear comrades. Each found himself in a situation that needs a gift and not just a gift, but something very interesting and original. Especially gift for your girlfriend loves guitar. Internet is limitless and as a bottomless pit has no end. After long wanderings over the vast expanses, it was decided to make a coffee table. This is the first of its kind. In my opinion turned out not bad. In the course of action I will comment on what is happening.
Was first bought a wooden shield required size. And in A1 format required stencil printed.
Since the shield was a bit more than what was intended and had to increase the size of the handles.
Armed with a jigsaw began the process of cutting out this miracle-shaped table. Dumb was the first time in the hands to keep the jigsaw. And it is necessary'm not zakosyachit.
About miracle first stage was successful. Severe cerebral process was waiting for me in the place where you had to make a smooth round holes. First drill was drilled small holes along the contour and then the same jigsaw were cut circles. Initially, it was difficult to call it a community. Similarity circles. Circles, they were only after aligning them with sandpaper to cut dressed kruglyashok and inserted into the drill.
When the ordeal was over with circles, it was decided to do a little rounded edge of the table, thereby eliminate irregularities he made a jigsaw. Well here it was difficult to automate the process and had to work handles. A piece of wood, sandpaper, first major, then smaller. And in the summer to do it as the second foul. Hands get tired, then go ten. But that will not do for his beloved.)) The morale support to friends and drink produced via fermentation of malt wort, and usually with the addition of hops. Bolt clear that beer.))
Form has been smoothed and again these circles. Too much, they stood their tangy. Had their smooth and slightly to grind off. Processing completed grinding medium, and then the finest sandpaper.
After the action moved from a dusty garage, balcony on the net. As the piece of wood was very bright and looked not so impressive and expensive, it was covered with several layers of water stains (oak). After the first coat immediately povylazili nezashlifovannye scratches are so nebyli visible. The second layer covering these scratches began a very personal look creating a grungy effect. It's a guitar fretboard (excuse)))
Then came the most difficult moment and glasses. It's one thing to work with a drill or bar with sandpaper, another small brush. A blueprint was dealt circuit Fender.
A night not so long already. Shaking hands with a lot of thoughts and phrases that would be worth all this zapikali and paint.
Wow. Almost everything is ready. The final touches on a pair of applying layers of lacquer.
Binding the three legs to our table.
And voila, done.
She was very happy. Later in the hole to insert cups in the color table.
That's all. Thank you for your attention.
Source:
