672
KIA
Remember March, the 10, the snow drifts to 2m in height? On the roads - some corresponding garbage, or slush, or ice ...
At this joyous time "in sandwich" pripechatat Korean domestic nine, which put the tires out of season ... To be exact - pereobulsya ahead of time ... rather - vodyatly ...
Not only that - a great gift for the owner Sportidzh became Azerbaijani registration vodyatla ...
For the money compensation Court it goes so far and it is not known when and where will come ...
100 pictures
Wings nalezli rear door
The wheels do not revolve
Muzzle too nabikren
When the snow melted it was a look
TV went
Rear left wheel has left forward together with all of the tailgate
To look at the damage we had to cut it out from inside the boot lid lock
When the lid is still opened - saw broken all plastic interior
We found a donor, dug out of a snowdrift ... or rather ...
And now taken
And prepared for transplant
Tighten sportidzh-snow dragged to the stocks
Winch puffs, because the rear wheels are not spinning
Tighten the front and rear at the same time pulls the gum back panel
That though the wheels began to scroll
The front is fixed to the Stacking clips and ass tearing crunching left rear wheel while never ceases to strike sharply on the wing
Is mounted on the stocks and to understand battered suspension
Throw off the gimbal
...
...
Remove the fuel tank with gasoline pump
Drain the fuel into the canister
The entire rear axle towards
Roughly cling Flew forward rear wing
And pull it roughly on the stocks reverse vector
Pulling a roll of metal that was later cut that
There is a special clamp that allows the two vectors pull jammed
We have this thing right here, and you want to
Pull pull
And even tear metal
We do better - easier to cut
Drilled on the rear panel of the nugget
Why, in a chaotic manner, they are made in the factory
Also otsverlivaem point welding chute compartment of the spar
That's what happened from the vent blow basin between the chute and the rear right wing
On the left we have not -those jams no spot welds, there we simply sawing back panel
Sipped
Relieve body
Hydraulic straightening lightened the load right rear spar
Hydraulic stretching back trying to place the inside of the left rear wing
The stump of the left rear spar with inhuman creaks, whistles take out back
Saw off useless basin chute
Sawed off, so much so that it is now possible to scratch the body of the sub-frame (to replace it, by the way, led him) :)
Sportidzh ass quite easily become
Excess is now only crumpled rear left wing
Take a cosmetic metal scissors :) and do Whack!
Surgical removal of the wing here - we left on the body just still alive, the whole
The door closes nowhere :)
The upper part of the wing - have porihtovat roof rack, there is a substitution we have nothing from the donor
Stub spar hold out to the landing position (for a new asshole)
Tighten its impact in an accident specifically
But we have to unwind!
Cooking donor for transplantation on this patient
That turned a handsome man with a loop - which will now close the door left back!
Sprinkles and butted with the help of the Bulgarian
Not for Trishka coat?
No - everything is fine!
With experience, which does not spend on drink, because that's this:
It turns out this is:
If you apply the tools nanotochnostyu - red stretch marks - a new spotridzha ass rise like a glove!
Only need to push with the right force at the right place, the atoms and the other board (if not the end - do not apply to the place) - you can squeeze the hood :)
That turns the wing as a native
Snapped the trunk lid to expose zazorchiki
And they loom just wing something sticking out of the right rear door
Pulling his arm like this (spotter manual effort, unfortunately, did not take such a jam)
But the hook 10-ton hydraulic - take it!
Butt ready
Tyutelka-in-tyutelku if the trunk lid with a finger "to shut»
And it confirms the rear bumper
Boil all the points and welds
At the rear
Coat with sealant and process rust preventative inner cavity
Replace the broken frame and suspension components for new
Putting all the updated suspension in place (only without wheels)
Rihtuem rear fender top
Ready to paint, leveling surface
Oh yeah ... we still have the same curve of the muzzle!
Lonzheronchiki look in all directions!
Here is broken, "TV" will replace the course
As magicians - at the same time we apply our new TV spars pull and tighten the left front mudguard (which attaches the wing front left)!
Muzzle ready
We prepare it for painting
Gruntuem back of the
Well, painted in two stages, first attachment:
Trunk lid, for example
With the hood
After being driven into the camera the whole body,
reveal the finishing surface roughness
Paste everything that does not need painting
...
Well, glory, all that is required:
...
...
Collects the results of our work
Plating plastic salon bought (instead of battered accident) - 50 thousand rubles
Putting a muzzle car
And then put out to dry sunlight
...
...
...
...
the end, and who was listening - well done!
and thank you for your attention
Source: http: //
At this joyous time "in sandwich" pripechatat Korean domestic nine, which put the tires out of season ... To be exact - pereobulsya ahead of time ... rather - vodyatly ...
Not only that - a great gift for the owner Sportidzh became Azerbaijani registration vodyatla ...
For the money compensation Court it goes so far and it is not known when and where will come ...
100 pictures
Wings nalezli rear door
The wheels do not revolve
Muzzle too nabikren
When the snow melted it was a look
TV went
Rear left wheel has left forward together with all of the tailgate
To look at the damage we had to cut it out from inside the boot lid lock
When the lid is still opened - saw broken all plastic interior
We found a donor, dug out of a snowdrift ... or rather ...
And now taken
And prepared for transplant
Tighten sportidzh-snow dragged to the stocks
Winch puffs, because the rear wheels are not spinning
Tighten the front and rear at the same time pulls the gum back panel
That though the wheels began to scroll
The front is fixed to the Stacking clips and ass tearing crunching left rear wheel while never ceases to strike sharply on the wing
Is mounted on the stocks and to understand battered suspension
Throw off the gimbal
...
...
Remove the fuel tank with gasoline pump
Drain the fuel into the canister
The entire rear axle towards
Roughly cling Flew forward rear wing
And pull it roughly on the stocks reverse vector
Pulling a roll of metal that was later cut that
There is a special clamp that allows the two vectors pull jammed
We have this thing right here, and you want to
Pull pull
And even tear metal
We do better - easier to cut
Drilled on the rear panel of the nugget
Why, in a chaotic manner, they are made in the factory
Also otsverlivaem point welding chute compartment of the spar
That's what happened from the vent blow basin between the chute and the rear right wing
On the left we have not -those jams no spot welds, there we simply sawing back panel
Sipped
Relieve body
Hydraulic straightening lightened the load right rear spar
Hydraulic stretching back trying to place the inside of the left rear wing
The stump of the left rear spar with inhuman creaks, whistles take out back
Saw off useless basin chute
Sawed off, so much so that it is now possible to scratch the body of the sub-frame (to replace it, by the way, led him) :)
Sportidzh ass quite easily become
Excess is now only crumpled rear left wing
Take a cosmetic metal scissors :) and do Whack!
Surgical removal of the wing here - we left on the body just still alive, the whole
The door closes nowhere :)
The upper part of the wing - have porihtovat roof rack, there is a substitution we have nothing from the donor
Stub spar hold out to the landing position (for a new asshole)
Tighten its impact in an accident specifically
But we have to unwind!
Cooking donor for transplantation on this patient
That turned a handsome man with a loop - which will now close the door left back!
Sprinkles and butted with the help of the Bulgarian
Not for Trishka coat?
No - everything is fine!
With experience, which does not spend on drink, because that's this:
It turns out this is:
If you apply the tools nanotochnostyu - red stretch marks - a new spotridzha ass rise like a glove!
Only need to push with the right force at the right place, the atoms and the other board (if not the end - do not apply to the place) - you can squeeze the hood :)
That turns the wing as a native
Snapped the trunk lid to expose zazorchiki
And they loom just wing something sticking out of the right rear door
Pulling his arm like this (spotter manual effort, unfortunately, did not take such a jam)
But the hook 10-ton hydraulic - take it!
Butt ready
Tyutelka-in-tyutelku if the trunk lid with a finger "to shut»
And it confirms the rear bumper
Boil all the points and welds
At the rear
Coat with sealant and process rust preventative inner cavity
Replace the broken frame and suspension components for new
Putting all the updated suspension in place (only without wheels)
Rihtuem rear fender top
Ready to paint, leveling surface
Oh yeah ... we still have the same curve of the muzzle!
Lonzheronchiki look in all directions!
Here is broken, "TV" will replace the course
As magicians - at the same time we apply our new TV spars pull and tighten the left front mudguard (which attaches the wing front left)!
Muzzle ready
We prepare it for painting
Gruntuem back of the
Well, painted in two stages, first attachment:
Trunk lid, for example
With the hood
After being driven into the camera the whole body,
reveal the finishing surface roughness
Paste everything that does not need painting
...
Well, glory, all that is required:
...
...
Collects the results of our work
Plating plastic salon bought (instead of battered accident) - 50 thousand rubles
Putting a muzzle car
And then put out to dry sunlight
...
...
...
...
the end, and who was listening - well done!
and thank you for your attention
Source: http: //
