1001
Restoring Lancer (52 photos)
If all the grandmothers who run across the track anywhere, threw off their pensions used the fund to pay for repairs of cars affected by their mad sprints ...
If all young patsanchiki on older boomers could reduce the average speed around the city with 120 ...
If Lancers pieces of ordinary RZD-rails were welded to the side members, instead of flimsy amplifiers bumpers ...
This sandwich would not be ...
Ass car warped to some smiley
Waves on the wing
Flimsy power rear bumper
And the front too ... flimsy
Throws the poor guy on the stand
And understand it to start work
Waves at the bottom of the spare wheel compartment and clamped
Here the tumor will have to be cut, delete
It comes directly understanding that we need a donor like this here:
Him and bring quickly enough from the suburbs
Here's how neatly on the back of the nugget otsverlen of unbeaten original Mitsu
Chainsaw ... just kidding ... Bulgarian snap off at the back of the car
Somehow we do wedding limos, when asked: remove the back panel - and then welds elongation and the back cover with the back of the beam and the suspension spread to several meters back ...
But this time, the owner has decided not to make a wedding limousine from his Lancer
In the hole insert a donor organ, and we catch him a few points of welding to draw and expose gaps had the opportunity
Hydraulic pull-up, anchoring welding
We put an entire boot lid, tightens finally all gaps
On the right side are also exhibiting all millimeters
And brew
Waves on the wing clean, obabatyvaem welded seams
Sealants are passed at the seams
Zadok ready
We dropped a crumpled front bumper amplifier and begin to pull the runaway spars
Next, try on a booster when things tightened - he stands up well to their rightful seats on the longitudinal members
Squeeze a "TV" instead of mint panel, here it is red for the amplifier
We try on body parts and put out all the gaps in the face Lancer
Car drives away in training, meanwhile battery lain next to the car during the body work - finally sat down, his booster enliven
Aligns the side of the vehicle at ground
It is this part of the back of the sealant - will be covered with fresh paint
To drive in the camera and to the full otkrasa car - repair places has already been set back panel
Irregularities of sealants and vyshtampovok should also be on the factory car - all leave
Beautiful turned back panel, varnish is applied here is not in the factory - we do it without varnish
Then the rest of the body gruntuem
And is ready for painting
Rolls into the camera, degrease all surfaces
Paste
And color
Power straight from the tin
All attachments, as it should be - paint separately
Suspended the so-called "helicopter" - could come to paint the inside of the parts
But already otkrashenny body collect
Chuck
Doors collect
And the back of the car with the trunk
Because of surprises - even shattered muffler while accident
Replace our slesarke
And here I am ready mitsubiska:
Lancer pulling out of a sandwich in nature:
If all young patsanchiki on older boomers could reduce the average speed around the city with 120 ...
If Lancers pieces of ordinary RZD-rails were welded to the side members, instead of flimsy amplifiers bumpers ...
This sandwich would not be ...
Ass car warped to some smiley
Waves on the wing
Flimsy power rear bumper
And the front too ... flimsy
Throws the poor guy on the stand
And understand it to start work
Waves at the bottom of the spare wheel compartment and clamped
Here the tumor will have to be cut, delete
It comes directly understanding that we need a donor like this here:
Him and bring quickly enough from the suburbs
Here's how neatly on the back of the nugget otsverlen of unbeaten original Mitsu
Chainsaw ... just kidding ... Bulgarian snap off at the back of the car
Somehow we do wedding limos, when asked: remove the back panel - and then welds elongation and the back cover with the back of the beam and the suspension spread to several meters back ...
But this time, the owner has decided not to make a wedding limousine from his Lancer
In the hole insert a donor organ, and we catch him a few points of welding to draw and expose gaps had the opportunity
Hydraulic pull-up, anchoring welding
We put an entire boot lid, tightens finally all gaps
On the right side are also exhibiting all millimeters
And brew
Waves on the wing clean, obabatyvaem welded seams
Sealants are passed at the seams
Zadok ready
We dropped a crumpled front bumper amplifier and begin to pull the runaway spars
Next, try on a booster when things tightened - he stands up well to their rightful seats on the longitudinal members
Squeeze a "TV" instead of mint panel, here it is red for the amplifier
We try on body parts and put out all the gaps in the face Lancer
Car drives away in training, meanwhile battery lain next to the car during the body work - finally sat down, his booster enliven
Aligns the side of the vehicle at ground
It is this part of the back of the sealant - will be covered with fresh paint
To drive in the camera and to the full otkrasa car - repair places has already been set back panel
Irregularities of sealants and vyshtampovok should also be on the factory car - all leave
Beautiful turned back panel, varnish is applied here is not in the factory - we do it without varnish
Then the rest of the body gruntuem
And is ready for painting
Rolls into the camera, degrease all surfaces
Paste
And color
Power straight from the tin
All attachments, as it should be - paint separately
Suspended the so-called "helicopter" - could come to paint the inside of the parts
But already otkrashenny body collect
Chuck
Doors collect
And the back of the car with the trunk
Because of surprises - even shattered muffler while accident
Replace our slesarke
And here I am ready mitsubiska:
Lancer pulling out of a sandwich in nature: