It-was, cut, painted, bought at dismantling the example here is the result?
It is not always so boring place complete repairs of cars ...
Sometimes it wakes up and begins to itch ... the soul of the owners of vehicles ...
Rebel soul wants for some reason at the end of body repair More ... and add a small storm!
And Bulgarian starts ... do!
Below are three former muzzle beaten three corresponding hood and a Bulgarian military (as Leonardo)!
60 photos
The Bulgarian cut, be careful,
... And the spark is no worse than sparklers!
Renovated bat muzzle one blue Lancer - we here in such a vehicle has appeared in the yard
Conventional hood owner does not want to put and tyuningovany something once detained its suppliers ...
Tired of waiting Exotic tyuninh-hood - we have offered to buy the owner of usual and our forces to style it ...
It told to do.
We rushed to the disassembly and found there a good variantik for tyuninhofff:
Next, we marked out the future elements of aggressive ventilation
With seven spans and one uncle - lined layout plan for future openings ...
Well, let them under the knife ...
Rezai first outside the hood
Coordinate holes snapped out - had to vnutryankoy hood, because there are amplifiers hood
They need to get around very carefully, because Most ventilation nozzles according to our idea will be bent inward
Internal amplifiers hood for only two of the seven (!) Future nozzles - took to spoil (but back then we brew and process, do not worry)
...
Main, the largest nozzle outwardly convex bonnet
...
Beneath it all intact and amplifiers
The rest of the vents - unproblematic, sawing
Here's what happened after the operation Saw benches
The main airbox our kapotika
...
The entire hood is cut ruthlessly chaotic ...
...
...
Then we bought here are things like strings for the guitar, is not it? :)
Who was the first to guess why they are needed - to respect and otherwise uvazhuha!
They took a donor sheet metal from another hood and mark it like this.
What for?
To make the walls of our aggressive air vents
Scrollsaw first wall
Baseline measurements department OTC :)
And welded to the wall of our nozzles, so they are not dangling in the wind :)
We clean the welds
In this form of the metal - it's very difficult ...
tyagomotina
Same (wall) perform with nozzles that are bent inward
And are ready to paint the hood
Displays all forms :)
slozhnosochinennye
Gruntuem
Threaded inside the ventilation holes just such an aluminum mesh
And paint everything with fishnet
Paint dries
Dress on the final chord of the tenth Lancer
And it turns out like this
...
And yet it would seem?
But next we repaired Lancer with such a blow that's muzzle
Where the hood, we have successfully Align
Owner corner of his eye he saw the blue tuning Lancer in the neighborhood with her - and did not put up with the usual appearance of his 10s and asked to make the first soul curled up, and then turned around like an accordion ...
And we have it here Navara such a monster at the site of the old hood :)
A close look will catch - concavity before the main air vent, this was done by cutting the elongated piece and be welded with little stenochku
And the very shape of the main vents - a heaped shape!
Paint outdoor advertising
...
And vnutryanku also paint, put on the mesh (in the hood - the owner decided to leave the black mesh, not paint)
There were problems with vnutryankoy much more (ten times more difficult) than with a blue hood
Since had cut and digest all the internal amplifiers for the implementation of the notorious vyemki- "vyshtampovki»
Here's the place missed the mark repair sealant
Putting the hood hang offal
...
Looks drive even more aggressively than blue:
...
...
Wedge on ventilation fans Mitsubishi understand-you :)
Well, just went to a booze - in a couple of words to tell you that the wedge holders knee-
We did about the same time (with the Lancer above) is not a simple repair golfiki muzzle, resulting in a machine that's taken shape
And I was presented with a new hood (remember the two previous car had broken with the goods and the hood respectively)
The owner raised a hand kramsat new hood, and he asked us to make him the following:
«Bad look» the so-called ... from the beautiful new hood was planed nose and is welded to it a strip of metal bent:
Otshpatlevano-aligned
After painting
And as a result - frowning face course :)
Source: