484
Safety system in an elevator
The selection of about 30 photo + slightly bukovok please do not break.
1. Putting the bulk of which in case of failure of equipment in the elevator does not allow him to fall freely, and inhibits it.
2. Collect the bottom of
3. fasten the lower part of the side walls
4. Good tighten all
5. rolled over everything and put on a strap with which this device in the elevator shaft ustanavlivaetsya
6. them we are also well-fasten.
7. establish blocking falling elevator device
8. good lubricating bolts salidolom
9. Screwing them where polozhenno
10. The same thing we do with the other Toroni device is almost ready
11. Adjust the remaining copper lining (takoyzhe effect it as the brakes in your car)
12. put a stop
13. All ties established due to not slam anything during transport, and placed in a box
14. Further cut the cable to connect electronics
15. The device for reading the amount of wind off the wire
16. The wound off after the desired number, serial number, and put the size of
17. Put in a box and pack
18. The glue on top of another box in which to kits with different facilities Furniture and bolts to install this devaysa
19. Box
20. Putting the hydraulic system by means of which clamping osuschestvlyaetsya brakes.
21. all twisted together
22. No more keys can not oboitis.
23. laid in a box
24. add the already pre-assembled kit with hoses and bolts
25. Collect the second box
26. All along the way are making a computer
27. The instruction of use, all the details of a picture, so that all will understand
28. After all the carefully laid, do cover the box with a large stapler
29. everything closes and tightens
30. and sticking sure the serial number
Dobavleno1 in [mergetime] 1285885274 [/ mergetime]
Here voopsche and all later posted a video like this device is tested.
Sorry for the quality, Fota from the phone.
Source:
1. Putting the bulk of which in case of failure of equipment in the elevator does not allow him to fall freely, and inhibits it.
2. Collect the bottom of
3. fasten the lower part of the side walls
4. Good tighten all
5. rolled over everything and put on a strap with which this device in the elevator shaft ustanavlivaetsya
6. them we are also well-fasten.
7. establish blocking falling elevator device
8. good lubricating bolts salidolom
9. Screwing them where polozhenno
10. The same thing we do with the other Toroni device is almost ready
11. Adjust the remaining copper lining (takoyzhe effect it as the brakes in your car)
12. put a stop
13. All ties established due to not slam anything during transport, and placed in a box
14. Further cut the cable to connect electronics
15. The device for reading the amount of wind off the wire
16. The wound off after the desired number, serial number, and put the size of
17. Put in a box and pack
18. The glue on top of another box in which to kits with different facilities Furniture and bolts to install this devaysa
19. Box
20. Putting the hydraulic system by means of which clamping osuschestvlyaetsya brakes.
21. all twisted together
22. No more keys can not oboitis.
23. laid in a box
24. add the already pre-assembled kit with hoses and bolts
25. Collect the second box
26. All along the way are making a computer
27. The instruction of use, all the details of a picture, so that all will understand
28. After all the carefully laid, do cover the box with a large stapler
29. everything closes and tightens
30. and sticking sure the serial number
Dobavleno1 in [mergetime] 1285885274 [/ mergetime]
Here voopsche and all later posted a video like this device is tested.
Sorry for the quality, Fota from the phone.
Source:
