587
Correction in a new window, part 1 - the sill
So, it's my time, and lay on his neck the yoke of the mortgage. Run off a bunch of lines and get a coveted Tug, I bought a modest odneshku. I will not be a nightmare quality of construction and the "ideal" walls, I think everybody knows how to build today, I will tell directly about the window.
There is one very correct saying "windows in the new building should be removed, remove and burn the forest" because it's a great way to save builders. But as the current crisis (and it is, believe me, just do not say much about it) did not allow raskidyvatsya finances left to right, it was decided to consider what can be done with the current windows.
14 photo.
That's actually the hero of the story:
With slots left and right blowing so that it seems as though there is a gnome fan sat down. But how secure the actual builders of the slopes, on the first picture I tore them. It drills with a concrete.
A little break your head, I decided to do some alteration of slopes is unlikely, so roll up your sleeves began to dismantle the current window sill. This is done quite elementary, get up to it, undertake both hands on the edge and gently but firmly pull the edge of the top;) weak plaster resists long
Then simply pull it toward you. Incidentally, from one side of the plug was in the end, with no other. Apparently ran out in the installation)))) Here is a picture after dismantling:
Some clues as to hint at the reasons for this quality of construction;))))
and by the way, the builders are also confident that this is a great place for an ashtray;)
That's actually how he looked below the sill. The empty spaces were wooden guide bars. Already I snatched.
I also tore foam. In general, under the sill should be empty, zapenivat all impossible. Because the battery warms the wall, the wall warm window sill, he, in turn, heats the window, not allowing the latter to fog.
Clean up the underside of the foam, foam and plaster:
That's the way from the barrel, at the corners of the huge gap. Dwarf was not found))
and two
To expose the guide bars, which lie sill:
Then they laid the windowsill. Use a level to watch to make it horizontally in both planes by having to put splinter (they wedges):
Then I took it off and propenyl the entire bottom of the window. In any case, propenyl, and the old foam. It does not inspire confidence in me;)
Why then is this image I did not do (((probably much carried away. Then we put in place the windowsill and again check on the level. That's how it looks from the outside wall (photo not yet propenyl):
Next is the bottom foam gently closed up to then it was easier to plaster. Let me remind you one more time, all space zapenivat impossible. And by the way, use low foam expansion to the window sill is not arched. In my case Penosil Gunfoam 65.
On top of that did not raise the window sill, put heavy boxes, the benefit to the lack of moving them there)) That's actually all further bottoms plastered stucco.
With slots sill no more blows, and now plan to change the seal on the windows / as blowing in several places of the window, and make normal slopes with plastic insulation.
Incidentally, the last photo. If someone does not know, here you can adjust the degree of pressing the window, in the summer is less dense, more winter. I half helped, but replace the seal still have; (((
Once again I say that this is my first experience, do not repairman, I do it for the first time. Just he decided to make the entire repair time permits now))) I will be glad to any comments, since there is still two windows and a balcony.
I have everything, thank you.
Source:
There is one very correct saying "windows in the new building should be removed, remove and burn the forest" because it's a great way to save builders. But as the current crisis (and it is, believe me, just do not say much about it) did not allow raskidyvatsya finances left to right, it was decided to consider what can be done with the current windows.
14 photo.
That's actually the hero of the story:
With slots left and right blowing so that it seems as though there is a gnome fan sat down. But how secure the actual builders of the slopes, on the first picture I tore them. It drills with a concrete.
A little break your head, I decided to do some alteration of slopes is unlikely, so roll up your sleeves began to dismantle the current window sill. This is done quite elementary, get up to it, undertake both hands on the edge and gently but firmly pull the edge of the top;) weak plaster resists long
Then simply pull it toward you. Incidentally, from one side of the plug was in the end, with no other. Apparently ran out in the installation)))) Here is a picture after dismantling:
Some clues as to hint at the reasons for this quality of construction;))))
and by the way, the builders are also confident that this is a great place for an ashtray;)
That's actually how he looked below the sill. The empty spaces were wooden guide bars. Already I snatched.
I also tore foam. In general, under the sill should be empty, zapenivat all impossible. Because the battery warms the wall, the wall warm window sill, he, in turn, heats the window, not allowing the latter to fog.
Clean up the underside of the foam, foam and plaster:
That's the way from the barrel, at the corners of the huge gap. Dwarf was not found))
and two
To expose the guide bars, which lie sill:
Then they laid the windowsill. Use a level to watch to make it horizontally in both planes by having to put splinter (they wedges):
Then I took it off and propenyl the entire bottom of the window. In any case, propenyl, and the old foam. It does not inspire confidence in me;)
Why then is this image I did not do (((probably much carried away. Then we put in place the windowsill and again check on the level. That's how it looks from the outside wall (photo not yet propenyl):
Next is the bottom foam gently closed up to then it was easier to plaster. Let me remind you one more time, all space zapenivat impossible. And by the way, use low foam expansion to the window sill is not arched. In my case Penosil Gunfoam 65.
On top of that did not raise the window sill, put heavy boxes, the benefit to the lack of moving them there)) That's actually all further bottoms plastered stucco.
With slots sill no more blows, and now plan to change the seal on the windows / as blowing in several places of the window, and make normal slopes with plastic insulation.
Incidentally, the last photo. If someone does not know, here you can adjust the degree of pressing the window, in the summer is less dense, more winter. I half helped, but replace the seal still have; (((
Once again I say that this is my first experience, do not repairman, I do it for the first time. Just he decided to make the entire repair time permits now))) I will be glad to any comments, since there is still two windows and a balcony.
I have everything, thank you.
Source:
