Why the Washing Machine Issues Errors and What Error Codes Mean

With the advent of a modern washing machine, our everyday life has become much easier! This miracle of technology is equipped with many useful functions, among which there is self-diagnosis of problems. Noticing a failure, the washing machine gives an error in the form of a code. It is thanks to the code on the display of the device that we can quickly determine the cause of the breakdown and fix it. But to understand what the machine is trying to tell you, you need to know what this or that error code means. The editorial will help you understand this. "Site".

The washing machine has an error .

Indesit, Ariston

1. F01 - problems with the drive motor due to short circuit in the control circuit.
2. F02 - there is no signal about the operation of the motor from the process generator to the electronic controller.
3. F03: Problems with the temperature sensor.
4. F04 - the machine signals a malfunction of the water level sensor.
5. F05 - Problems with water discharge.
6. F06 is a signal about the faulty buttons in the CM series in the Ariston Dialogic line.
7. F07 - The machine warns that the heating element is not submerged in water.
8. F08 - Failure of the heating element.
9. F09: An electronic control failure.
10. F10 is an error in the water level sensor.
11. F11 - problems with the drain pump.
12. F12: Problems in communication between the electronic controller and the display module.
13. F13 - failure in drying (failed control network t0).
14. F14 - failure in drying (drying is not included).
15. F15 - Failure to dry (drying does not turn off).
16. F17 - an error in the operation of the lock (the door is not closed tightly).
17. F18 is a microprocessor error.

Candy

1. E01 - problems in the operation of the locking device door.
2. E02 is a signal of water supply problems: its level does not reach or exceeds the norm.
3. E03 - problems with the water drainage system.
4. E04 - the machine signals a malfunction of the water filling system: its level exceeds the norm.
5. E05 - problems with the temperature sensor, no water heating.
6. E07 - a signal about a problem with the drive motor (failed technogenerator).
7. E09 - failure of the drive motor (the shaft does not rotate).

ASKO

1. E01, Motor fault - errors in the operation of the drive.
2. E02, Water inlet fault - a signal about problems with water collection.
3. E03, Draining fault - problems in the drainage system.
4. E04 – The machine signals that it cannot supply enough water.
5. E05, E06 - problems with water heating.
6. Door lock fault - the washing machine door is not tightly closed.
7. Floaming - increased foaming.
8. Overfilling, Over flov - water in the washing machine tank.
9. Termistor fault is a temperature sensor error.
10. Pressure Sensor Error – The water sensor is defective.

SAMSUNG

1. E1 is a water dialing error.
2. E2 - problems when draining water from the system (the drain time is different from that set by the manufacturer).
3. E3 – when dialling water, the “overflow” level is reached.
4. E4 – the amount of laundry loaded into the washing machine exceeds the norm.
5. E5, E6 - problems with water heating.
6. E7 is an error in the water sensor.
7. E8 - the temperature regime is not observed.
8. E9 - washing machine signals water leakage.

LG

1. PE - problems in the operation of the water level sensor.
2. FE - overflow of the tank with water.
3. dE - problems with the door locker (check if it is tight enough).
4. IE – water dialing problems: The washing machine cannot get enough fluid.
5. OE - drain problems: you need to check the condition of the hose and filter.
6. UE is a violation of drum balance.
7. tE - the temperature regime is not observed.
8. LE is an error in the locking mechanism.
9. CE - washing machine signals overload of the drive motor.
10. E3: The system cannot detect the load.
11. AE - failure in the auto-off system.
12. E1 - leakage of water in the pallet.
13. HE - The heating tent is broken.
14. SE - the system detected an error in the drive motor switch.

KAISER

1. E01 - no signal to close the hatch: washing will be stopped.
2. E02 - the machine signals that the filling time of the tank exceeded 2 minutes. The system continues to wash.
3. E03 - the water drain exceeded 1.5 minutes.
4. E04 - the machine signals the problem of water filling (overflow of the tank). At the same time, the system stops washing and turns on the drain pump.
5. E05 is the problem of pouring water. If after 10 minutes no signal is received from the sensor "Nominal level", the machine stops washing.
6. E06 is a drain problem. If after 10 minutes there is no signal from the "Empty tank" sensor, the machine stops washing.
   
   
   
   
7. E07 - leakage of water into the pallet.
8. E08 - the parameter of the supply network does not correspond to the norm. Manufacturers recommend a voltage of 190-253 volts.
9. E11 - a failure of the hatch lock was detected.
10. E21 is an error in the operation of the drive system. The laundry stops.
11. E22 - the drive motor rotates on its own, without a start command.
12. E31 - a malfunction of the temperature sensor (most likely, this was preceded by a short circuit in the circuit).
13. E32 - malfunction of the temperature sensor (chain break).
14. E42 - malfunction, the hatch was locked within 2 minutes after washing.

Electrolu, Zanussi

1. E11 - the machine found a problem with the water supply.
2. E13 - water leakage in the pallet of the washing machine.
3. E21: Water has not been removed from the tank for 10 minutes.
4. E23 - the machine signals the breakdown of the simistor (control element of the drain pump).
5. E24 - the occurrence of problems with the drain: the system detected malfunctions in the symistor circuit of the drain pump.
6. E33 - uncoordinated operation of water level sensors.
7. E35 - the problem of water filling was found. The water level in the working tank is above normal.
8. E36 is a breakdown of the sensor, which warns about the inclusion of the tent in the absence of the required amount of water.
9. E37 - a malfunction of the water level I sensor was detected.
10. E39 - malfunction of the transfusion level sensor.
    
    
    
    
11. E41 - the washing machine door is not tightly closed.
12. E42 - the system recorded a malfunction of the locking lock of the hatch.
13. E43 - malfunction of the lock lock simistor.
14. E44 - the system detected a breakdown of the hatch closure sensor.
15. E45 - malfunction in the control circuit of the hatch lock (in the electronic controller).
16. E51 - breakdown of the drive motor, which was preceded by a short circuit in the control element - the simistor.
17. E52 – no contact between the electronic controller and the tachogenerator.
18. E53 - a violation of the control circuit of the drive motor.
19. E54 - failure of one of the two contact groups of the reversible drive motor relay.
    
    
    
    
20. E61 - the temperature is broken, the water does not reach the temperature set by the program.
21. E66 - the system detected a malfunction of the ten relay.
22. E71 - violation of the temperature sensor (increased resistance).
23. E82 - the system detected problems in the work of the selector (a special device for selecting programs and cycles).
24. E83 - the system detected an error when reading data from the selector.
25. E84 is a washing machine configuration error.

BOSCH

1. F01 - Hatch door open.
2. FO2 - Water is not being drawn.
3. FO3 - Water doesn't drain.
4. FO4 - Water is leaking.
5. E02 - Engine problem.
6. E67 - Module encoding shot down.

Hansa

1. E01: There is no warning signal to close the door.
2. E11 - malfunctions in the power supply chain locking the door.
3. E02 - the tank is filled with water to the desired mark in more than two minutes.
4. E05 - the tank is filled to the desired mark in more than ten minutes.
5. E03 - the water drain time exceeded 1.5 minutes.
6. E06 - 10 minutes after the water drain, but the pressostat does not signal "the tank is empty".
7. E09 - during pressing there was too much foam, which could not be removed.
8. E04 is a signal that the tank is overflowing with water.
9. E31 - closing in the temperature sensor.
10. E32 is the break of the temperature sensor.
11. E21 - The drive motor is blocked.
12. EOB - the parameters of the supply network are violated.
13. E22 is a signal about the rotation of the drive motor without a command.
14. EO7 - water sensor "AquaStop" recorded water leakage into the pallet.
15. E42 - Program executed, but the door remains locked for more than two minutes.
16. E52 is a memory failure.

It's good to have a cheat sheet to help you out. Now you know what to do if the washing machine makes a mistake. Save the article.Not to lose it. Good luck!