1217
Making a table with carved lions
As promised, I spread another topic for the manufacture of table carved with lions.
Material products - Chestnut.
Will be 29 photos and videos if you get one at the request of some visitors on how the process goes.
1. machined on a lathe first part - a central table leg
2. In this part acanthus leaves and cut out patterns in the form of scales (to be seen at the end of
3. ...
4. Then start manufacturing three-feet of lions, here's one of them sawed
5. Feet waiting dokleyki extra thickness in places where there is a muzzle, mane and foot, and yet undertake and make harvesting wings. Yes, winged lion will!
Harvesting of the wing is ready ... it will be dressed right leg lion
6. Here is clad leg with her wing.
7. Now the actual fun begins, we start a thread, cut the feathers on the wings, etc ...
8. ...
9. ...
10. ...
11. ... that's got a wing!
12. Then start to cut the lion's paw, first leg on the workpiece dokleiv additional mass of wood, the photo shows, the very paw of the total thickness of the workpiece.
Workpiece thickness 46mm and 25mm dokleeno both sides
13. Side view
14. ...
15. Here's a turned leg ... go ahead
16. Turning to the most difficult part, the face of the lion. The photo shows the three stages of production, the first is glued solid wood, on the second extra weight lifted and the third ready to face
17. Front
18. ...
19. ...
20. Now it came to the mane, so to call it. In order to make it the bulk, weight and dokleivalas wood on the sides
21. General view of the legs and everything to do with it, or rather all three
22. ...
23. For a time, not photographed, it was made progam lower and upper supports under the table top.
Also, the assembly process is not photographed in a hurry, the process is not complicated, it was all collected in the dowel and tie and glue PVA. Customer requested only that the wings were glued to the progam and carved legs, and the rest to understand. So they did.
So enjoy the finished product ... a few pictures, the end will tell
24. The view below ...
25. ...
26. General view of
27. I forgot to say about the table top, it is made of MDF, lining threaded oak veneered with natural oak veneer! All technology
28., ...
29. That last photo! Now your komenty! I later try to throw out video. Thank you for your patience!
Source:
Material products - Chestnut.
Will be 29 photos and videos if you get one at the request of some visitors on how the process goes.
1. machined on a lathe first part - a central table leg
2. In this part acanthus leaves and cut out patterns in the form of scales (to be seen at the end of
3. ...
4. Then start manufacturing three-feet of lions, here's one of them sawed
5. Feet waiting dokleyki extra thickness in places where there is a muzzle, mane and foot, and yet undertake and make harvesting wings. Yes, winged lion will!
Harvesting of the wing is ready ... it will be dressed right leg lion
6. Here is clad leg with her wing.
7. Now the actual fun begins, we start a thread, cut the feathers on the wings, etc ...
8. ...
9. ...
10. ...
11. ... that's got a wing!
12. Then start to cut the lion's paw, first leg on the workpiece dokleiv additional mass of wood, the photo shows, the very paw of the total thickness of the workpiece.
Workpiece thickness 46mm and 25mm dokleeno both sides
13. Side view
14. ...
15. Here's a turned leg ... go ahead
16. Turning to the most difficult part, the face of the lion. The photo shows the three stages of production, the first is glued solid wood, on the second extra weight lifted and the third ready to face
17. Front
18. ...
19. ...
20. Now it came to the mane, so to call it. In order to make it the bulk, weight and dokleivalas wood on the sides
21. General view of the legs and everything to do with it, or rather all three
22. ...
23. For a time, not photographed, it was made progam lower and upper supports under the table top.
Also, the assembly process is not photographed in a hurry, the process is not complicated, it was all collected in the dowel and tie and glue PVA. Customer requested only that the wings were glued to the progam and carved legs, and the rest to understand. So they did.
So enjoy the finished product ... a few pictures, the end will tell
24. The view below ...
25. ...
26. General view of
27. I forgot to say about the table top, it is made of MDF, lining threaded oak veneered with natural oak veneer! All technology
28., ...
29. That last photo! Now your komenty! I later try to throw out video. Thank you for your patience!
Source:
