333
How to repair a mirror
If you have a broken mirror, not in a hurry to go to the car wash.
Maybe you will be able to fix it by hand, using these instructions.
21foto!
1. Remove the mirror from the rear side
2. warmed termofenom mirror surface and put in plastic cards, to further dismantle the plastic frame mirror
3. Periodically, warming termofenom neatly stuck on cards
4. The periodic warming with a hand mirror hand mirror accurately disunite thermocouple and a housing.
5. The thermal tape glued to the mirror. As you can see, there is nothing damaged.
6. warmed mirror of the thermal tape peeled off from the mirror. (I have not got it very carefully because of the weak warming). Then tear off the film is not necessary, but I continued dismantling of curiosity and ...
7. completely peeled off the film from the mirror
8. Measure the resistance between the contacts and got something like 30 ohms.
If the resistance could not be measured, it would have to make a hole next to the terminal and the other to measure there.
And I was lucky and I immediately found the damaged compound
(There is visually seen what contact does not work, the conductor on the film becomes a little darker).
9. done in film hole to detect broken terminals
10. This is the future conductor. From it will only need the leg
11. Did Phillips slot in the film using "Paper Cutter" anointed acid solder slot,
I put the smallest rivet with a washer and riveted hammer on a vice.
JERSEY advance, you must smear solder acid and solder proludit part of the outside.
12. The acid itself. When dry, it forms a thin conductive film.
13. Solder the leg by radio to the washer and to the faulty contact.
14. Cheers, have a contact resistance of 27 Ohm, Ohm floor weigh my wires =)
15. Stick to the mirror dvuhstronny Foil scotch
16. glued to the mirror film
17. In the film again, stuck tape, I advise you to stick a porous double-sided tape thickness of 1.5-2 mm, it would be better to keep.
18. Slightly heating termofenom adhesive surface, to establish a framework and a good mirror pressed
19. The place of repair.
20.
21. Connected to the power supply for verification. Heated floor eats amp.
You can set and saved money can be spent on something useful or tasty.
source
Source:
Maybe you will be able to fix it by hand, using these instructions.
21foto!
1. Remove the mirror from the rear side
2. warmed termofenom mirror surface and put in plastic cards, to further dismantle the plastic frame mirror
3. Periodically, warming termofenom neatly stuck on cards
4. The periodic warming with a hand mirror hand mirror accurately disunite thermocouple and a housing.
5. The thermal tape glued to the mirror. As you can see, there is nothing damaged.
6. warmed mirror of the thermal tape peeled off from the mirror. (I have not got it very carefully because of the weak warming). Then tear off the film is not necessary, but I continued dismantling of curiosity and ...
7. completely peeled off the film from the mirror
8. Measure the resistance between the contacts and got something like 30 ohms.
If the resistance could not be measured, it would have to make a hole next to the terminal and the other to measure there.
And I was lucky and I immediately found the damaged compound
(There is visually seen what contact does not work, the conductor on the film becomes a little darker).
9. done in film hole to detect broken terminals
10. This is the future conductor. From it will only need the leg
11. Did Phillips slot in the film using "Paper Cutter" anointed acid solder slot,
I put the smallest rivet with a washer and riveted hammer on a vice.
JERSEY advance, you must smear solder acid and solder proludit part of the outside.
12. The acid itself. When dry, it forms a thin conductive film.
13. Solder the leg by radio to the washer and to the faulty contact.
14. Cheers, have a contact resistance of 27 Ohm, Ohm floor weigh my wires =)
15. Stick to the mirror dvuhstronny Foil scotch
16. glued to the mirror film
17. In the film again, stuck tape, I advise you to stick a porous double-sided tape thickness of 1.5-2 mm, it would be better to keep.
18. Slightly heating termofenom adhesive surface, to establish a framework and a good mirror pressed
19. The place of repair.
20.
21. Connected to the power supply for verification. Heated floor eats amp.
You can set and saved money can be spent on something useful or tasty.
source
Source:
