Still, automakers sometimes wedge-themed space :)
Judge: Chevrolet Starcraft, Honda Shuttle, Toyota Starlet ...
Ford generally stuck to the space: Galaxy, Aerostar, Orion, Taurus ...
And Mitsubishi is not far behind - captured from space star - welded metal Space Star ...
The design, of course, difficult to find a spaceship ... But grinder to cut something with a touch of space and stars always nice :) Anticipating the arrival of a tow truck the following description of the situation on the road:
"In general, washed up on a wet road into oncoming traffic and was hit in the right rear side of the little sliding back ...
In principle, the right rear wheel is spinning, but with difficulty, and his slightly arched at an angle, so on their own scary to go somewhere. »
Client confused, of course, right to left ...
Here - go to starboard, in principle, not terrible ...
But the left - really scary.
Wheel scratching wing
A salon can peek through a crack
Well, not only the back part of the body affected by the oncoming lane ...
He came to us not the whole star, but rather two-thirds of cosmo-star
Short body
If you look back - mash notably, body style left-back did not even guessed
The trunk lid "scratched" rear seatbacks
How could survive rear left pane - inexplicably!
The inscription «Space Star» a wave
But the car still knee - the plant and if this is to cut the wing on the lid - even go!
Donor we dug quickly, a week
Cut in the back of us right from the suspension
By mid-pillars
And two inches from the factory weld on the bottom
Curl up with a donor all that will stop welding, the hub of the wheels leave
Ready for a replacement!
Winch dragged to the stocks
Unveiling iron bouquet :)
Parse rear compartment
And see how the left wheel and the reception which followed the wave chute compartment
Fasten tightly the car clamps on the stocks
We throw off everything that hinders our work on the bottom, starting with the muffler
And ends with a bare bottom
Cut the window, throw off the remnants of optics and ready for the back of the bodywork
Close interior tarpaulin take grinding wheel and sawing space!
Sawing ruthlessly, indeed, fly space stars!
Cut and outer metal and amplifiers
The bottom sawing directly in millimeters from the factory seam - to make then dock with the donor seam
Finish unpack, everything is held by a thread, look at the lengths of cloth ...
Bang and a huge ass falls!
Cuts are beautiful on the body
Eliminated the entire tumor, all wrinkled and crooked
Pulls out a crumpled ass, here is a place for the future of a joint tailgate
The stocks we remove the severed limb cut off directly with the bat in the trash suspension
Her only way to scrap ...
In the air, hang remnants of cosmic star
This is not the star, but the capsule is some alien
Docking of the complex UNION APOLLO :)
To deadhead slipway just dragged Apollo - his right, too low orbit ...
But for the right connections - we still need to work on the hydraulics ...
Since we have clearly detected the curvature of the opening rear door, roof and power rear wing
One part of the body fix, and are putting in another 10 tons of hydraulic force
Try on the donor ...
And hold out again ...
Try on again ...
Connecting orbits must be matched directly on the nugget
Those. we are talking about millimeters instead of plus or minus 5cm :)
On the bottom here reamed holes - a factory welded point, we cleared them and sealant prepared for docking
Jacks for connecting a new asshole height
From left to put it mildly - not all smooth
Auntie is not aunt ...
Tolley ass is not the felts Space-old from another galaxy ...
Tolley slipway we are not yet fully worked - rolls hydraulic column on the left side and pull!
More sprinkles and kiss boo the trunk lid to the gaps at openings align
We catch crocodiles millimeters ass tightened on to the cosmic body
Do the right tack welding
And you're ready to scalding - all clearances received, everything is closed!
That is what we have prepared the window for the external metal
provarivaniya
And the inner metal track then
Cook a solid outer seam metal
Handle it inside anticorrosive
And brew window inner metal sealant are passed along the seam
The same algorithm is repeated on the other seams
That boil amplifiers threshold (where the staff hole is available), then treat it as anticorrosive and heat sealing window of the outer metal
The seams on the outer metal racks we clean the grinder to smooth the surface
At the bottom of the boil point, welded amplifiers, reproduced inside seam sealant is factory
And also outside seam sealer, just cover it with plenty anticorrosive
Keyword - abundant
When dried up anticorrosive - tank and collect all podnagotnuyu
We put the car on the suspension and the wheels are no longer curves
And we begin to prepare the entire perimeter of the body to paint
Jumped on welded rack spatula putty
And almost all of this putty vyshkurivaetsya forming a completely flat surface
That's what the mountain of waste shpatlevalnoy dust removal after surgery wing "zero»
Development unit (black) to pass on the details, revealing the remains uneven
Ready to paint
ANTIKOR cover internal seams
All stained vnutryanku
Gruntuem whole body and add-on parts for outdoor painting
And its beauty body
External parts
Such as the boot lid with the two sides
We hang on the body otkrashennoe attachments
Cut off the tumor waiting Metalworkers recycling
A star of the space we collect, glue in glass
And thoroughly laundered
Well, there you have the result of the downed space-star'a:
Or as if from outer space to park on the earth asphalt
I'll be back!
Source: autobotanik.livejournal.com