776
There are things to do
1. Finally, some free time and I decided to update its own set of brushes for makeup.
24 photos
2. That's what we need: satin ribbons (about 10 m.), Crayons, pins, ruler, centimeter, thread and needle.
3. Remove the measurements - height and width, 18 and 14, respectively.
4. Cut the ribbons we desired length + 1, 5-2 cm. In reserve. The edges of the burn, so as not to pushilis.
Spread as we like, and namёtyvaem hand, not to lose.
And start twisting our ribbons staggered. The edges of the anchoring pins.
It looks like after the weaving.
Try on - excellent size fits (did like the first time, and despite the calculations, afraid to make a mistake).
Now let's just old and ragged case: remove side tape ripped off by the end of the topcoat.
So, now we take kruglogubtsy and gently'll get the magnet-mount. Inside is an old cardboard box (apparently for edge hardness), it also take out.
Everything will wash thoroughly and leave to dry.
Net Case spread on a cloth and namёtyvaem, so as not to move out. Basting on three sides, except for the one where we insert the magnet.
The stitching.
Intermediate result.
Insert the magnet. Did not have to cut the ribbon, perfect stood between us.
Of tetrad cover Cut a piece of 8h12 cm., Put into the place of the old and worn, all namёtyvaem and sews.
Now cut off all protruding edges ribbons.
Immolation edge.
.
It is necessary to finish the edges. Take the longest of the remaining tape, cut in half, down and right sides sewn
It turns out that's the sort of thing.
All these manipulations were necessary, because not everything is calculated. Naive to believe that just one tape width enough to handle edge
At the edge of the product and wrap tape baits first hand.
Sewn - and voila! Everything is ready.
View from inside.
And from the outside.
Got a little sloppy, but I'm happy! The first experience can be considered successful.
24 photos
2. That's what we need: satin ribbons (about 10 m.), Crayons, pins, ruler, centimeter, thread and needle.
3. Remove the measurements - height and width, 18 and 14, respectively.
4. Cut the ribbons we desired length + 1, 5-2 cm. In reserve. The edges of the burn, so as not to pushilis.
Spread as we like, and namёtyvaem hand, not to lose.
And start twisting our ribbons staggered. The edges of the anchoring pins.
It looks like after the weaving.
Try on - excellent size fits (did like the first time, and despite the calculations, afraid to make a mistake).
Now let's just old and ragged case: remove side tape ripped off by the end of the topcoat.
So, now we take kruglogubtsy and gently'll get the magnet-mount. Inside is an old cardboard box (apparently for edge hardness), it also take out.
Everything will wash thoroughly and leave to dry.
Net Case spread on a cloth and namёtyvaem, so as not to move out. Basting on three sides, except for the one where we insert the magnet.
The stitching.
Intermediate result.
Insert the magnet. Did not have to cut the ribbon, perfect stood between us.
Of tetrad cover Cut a piece of 8h12 cm., Put into the place of the old and worn, all namёtyvaem and sews.
Now cut off all protruding edges ribbons.
Immolation edge.
.
It is necessary to finish the edges. Take the longest of the remaining tape, cut in half, down and right sides sewn
It turns out that's the sort of thing.
All these manipulations were necessary, because not everything is calculated. Naive to believe that just one tape width enough to handle edge
At the edge of the product and wrap tape baits first hand.
Sewn - and voila! Everything is ready.
View from inside.
And from the outside.
Got a little sloppy, but I'm happy! The first experience can be considered successful.
